ID: 2459
Open
Listing ID: #2459 has been added to your wishlist.
Description
PART: 12572-E - PRESS GLUING MACHINE - RADIO FRECUENCY - SOLID WOOD - OGDEN
USED - GOOD CONDITION
Curing area: 36” x 60” x 2” thick
Clamping pressure is applied by multi-power - dual pistons on a common shaft - pneumatic cylinders to maximize pressure while relying on standard plant pressures. Unlike presses without multi-power cylinders, which require booster compressors, the Model SL36x60 reaches full capacity at 100-psi plant air pressure.
Edge pressure is applied by eight pusher shoes, each with a 4” bore x 4” stroke twin-piston multi-power pneumatic cylinders.
Top platen pressure is applied by two 5” diameter x 16” stroke pneumatic cylinders through a cantilever arm that keeps the footprint to a minimum while still allowing the operator full access to the platen area.
The platen is set at a 45-degree angle and the top platen opens wide; allowing the operator to step inside the press for ergonomic and accurate parts placement.
The internal solid state RfsProtech 6KW Generator cures approximately 600 square inches of glue line per minute.
The Generator features solid state rectifiers and all aluminum cabinet for maximum conductivity and superior performance.
Two-hand no-tie-down safety controls for closing the top platen.
Controls are simple to understand, and are complete with the required push-buttons, switch, meters, digital operator display, and on-screen troubleshooting diagnostics.
The machine is controlled by a PLC for dependability and efficient maintenance. All controls will be provided for safe and efficient operation. The operator screen permits efficient operation, and the included press diagnostics screens assist in trouble-shooting when the need arises.
Proper interfaces will be provided for operational signals and emergency system stop.
All necessary RF controls, including buttons, meters, and PLC operator interface panel are mounted on a control panel attached to the left front of the press.
Interlocked top platen and safety switches on all access doors insure operator safety.
Power requirements are 480 volt, 60 cycle, 3 phase electric.
Circuit breaker protection is provided. A service disconnect is required for safety, but is not provided.
Powered In-Feed table with motor and controls
Out-feed steel deck
Voltage 480 volts 60 Hz
Payments & Returns
- Payment Methods
- Bank Wire Transfer
Post Message
Sign in to ask the seller a question.
AMXmachine
PART: 12561 - HORIZONTAL BAND RESAW - GRIZZLY G0504
PART: 12561 - HORIZONTAL BAND RESAW - GRIZZLY
G0504
In Good Running Condition
& Ready to ShipMain motor: 25HP, 220V/440V*
(prewired for 220V), 3-phaseElevation motor: 1/2 HPHydraulic pressure: 1000 PSIBelt Powered Hydraulic Pump -
Main Saw Motor - 25HPMaximum cutting capacity:
10" x 16"Distance from blade to
conveyor table: 1/4"–10"Feed speed: 0–61 FPMSaw blade size: 180" L x
1" WSaw blade speed: 7300 FPMFloor to table height:
40"Infeed table: 106" L x
16" WInfeed belt: 215-3/4" ...
AMXmachine
PART: 12526 - CNC MACHINING CENTER - ROVER GOLD 1232
PART: 12526-E - CNC MACHINING CENTER - ROVER
GOLD 1232USEDNumerically controlled machining centre ROVER
GOLD 1232Working fields: X = 3.280 mm; Y = 1.260 mm; electrospindle axis
Z Clearance = 180 mm with H=74 mm modules – Z
Stroke = 364 mmWORKING TABLE
6 ATS panel supports - L = 1240 mm - 18 sliding bases for vacuum
6 back stops of 115 mm stroke and 26 mm height spacers
6 front stops of 140 mm str...
AMXmachine
PARTE: 2GM-PSR - ROLADORA ELECTRICA - 50" ANCHO
PARTE:
2GM-PSR - ROLADORA ELECTRICA - 50" ANCHOPARTE: 2GM-PSR-5016 – ROLADORA - 50” x 16GA - 1 HP, 220/440V, 3 PHPARTE: 2GM-PSR-5016-1PH – ROLADORA - 50” x 16GA - 1.5 HP, 220V, 1 PHPARTE: 2GM-PSR-5014 – ROLADORA - 50” x 14GA - 1.5 HP, 220/440V, 3 PHFeatures:- ISO 9001 certified- Heavy welded all steel construction for maximum rigidity- Silence electrical motor- Quick release top roller- Two Powered driven Rolls- Precision ground rollers- 1” roll opening- All three rolls are made o...
AMXmachine
PARTE: 2GM-WDC-FP40 - COLECTOR DE POLVOS PARA METAL - 2,100 CFM - 5 HP
PARTE: 2GM-WDC-FP40 - COLECTOR DE POLVOS PARA METAL - 2,100 CFM - 5 HPElectrics: 220/440V, 3 PH2,100 CFM, 5 HP for 2MA-FP-2560 & 2MA-FP-4075 Metal SandersInlet opening: 8"Wet dust collection systems offer more safe and efficient method for collection of hazardous grinding/sanding/cutting dust generated by a variety of processes.The CAT wet dust collector offers many superior features.CABINET - made of welded stainless steel constructionFRONT DOOR - easily removed for maintenance & cleaning and e...