ID: 2459
Open
Description
PART: 12572-E - PRESS GLUING MACHINE - RADIO FRECUENCY - SOLID WOOD - OGDEN
USED - GOOD CONDITION
Curing area: 36” x 60” x 2” thick
Clamping pressure is applied by multi-power - dual pistons on a common shaft - pneumatic cylinders to maximize pressure while relying on standard plant pressures. Unlike presses without multi-power cylinders, which require booster compressors, the Model SL36x60 reaches full capacity at 100-psi plant air pressure.
Edge pressure is applied by eight pusher shoes, each with a 4” bore x 4” stroke twin-piston multi-power pneumatic cylinders.
Top platen pressure is applied by two 5” diameter x 16” stroke pneumatic cylinders through a cantilever arm that keeps the footprint to a minimum while still allowing the operator full access to the platen area.
The platen is set at a 45-degree angle and the top platen opens wide; allowing the operator to step inside the press for ergonomic and accurate parts placement.
The internal solid state RfsProtech 6KW Generator cures approximately 600 square inches of glue line per minute.
The Generator features solid state rectifiers and all aluminum cabinet for maximum conductivity and superior performance.
Two-hand no-tie-down safety controls for closing the top platen.
Controls are simple to understand, and are complete with the required push-buttons, switch, meters, digital operator display, and on-screen troubleshooting diagnostics.
The machine is controlled by a PLC for dependability and efficient maintenance. All controls will be provided for safe and efficient operation. The operator screen permits efficient operation, and the included press diagnostics screens assist in trouble-shooting when the need arises.
Proper interfaces will be provided for operational signals and emergency system stop.
All necessary RF controls, including buttons, meters, and PLC operator interface panel are mounted on a control panel attached to the left front of the press.
Interlocked top platen and safety switches on all access doors insure operator safety.
Power requirements are 480 volt, 60 cycle, 3 phase electric.
Circuit breaker protection is provided. A service disconnect is required for safety, but is not provided.
Powered In-Feed table with motor and controls
Out-feed steel deck
Voltage 480 volts 60 Hz
Payments & Returns
- Payment Methods
- Bank Wire Transfer
Post Message
Sign in to ask the seller a question.
AMXmachine
PART: 3AU-DEBU1000 – METAL - BRUSH SANDER – CAPACITY 1000 MM WIDTH
PART: 3AU-DEBU1000 – METAL - BRUSH SANDER – CAPACITY 1000 MM WIDTHNew with warrantyRound Chamfering Machine produces a surface so smooth that a nylon stocking is not snagged. AuDeBu1000 is a deburring machine specializing in round chamfering and capable of simultaneous treatment of large quantities of small-size work and medium-size work up to 1,000mm wide. Round chamfering of product edges has become the standard in sheet-metal processing. As the demand for round chamfering increases, we ca...
AMXmachine
PART: 1AM-3011-E – ROLLER STAND - INFEED - OUTFEED - 120 CM (47”) LENGTH - WITH GUIDE AND STOP
PART:
1AM-3011-E – ROLLER STAND - INFEED - OUTFEED - 120 CM (47”) LENGTH - WITH GUIDE
AND STOPSIDE
ROLLER TABLES Use
with saws, planers, edgebanders, jointers, etc.New
with warranty120
cm (47”) length x 39 cm (15.35”) widthVariable
height 83 - 87 cm (32.5 - 34.25”)Support
large and heavy wood pieces and wood panelsAdjustable
heigh to pair with your current machines7 galvanized steel ball bearing rollers-
1 back guide to avoid material to fall-
1 block stop to make same size ...
AMXmachine
PART: 12420 - DIMTER OPTICUT 260 THROUGH FEED OPTIMIZING LINE
PART: 12420 - DIMTER OPTICUT 260 THROUGH FEED
OPTIMIZING LINE
USED - VERY GOOD CONDITIONS
Year of Manufacture: 2018
Condition: Excellent
Electric: 460 Voltage 60 Cycle 3 Phase
GREAT CONDITION HIGH SPEED INFEED 750 FPM. LESS
THAN 1000 HOURS ON THIS MACHINEWorking dimensions:Cross sectionmin./max 0.48"- 10.23" width;
.25" - 3.15" thickness.Min. part length 5.5" cut.Length min/max 15.75"- 16'0".Motor: 10 HP vario speed to reduce board gap;
servo controlled up to 825 FPM.Saw: Blad...
AMXmachine
PART: 12576 – VERTICAL PANEL SAW - HOLZHER 1265 SUPER CUT
PART: 12576-E – VERTICAL PANEL SAW - HOLZHER
1265 SUPER CUT
USED – GOOD CONDITIONS
Capacity: 75″ x 169″
Depth of Cut: 2″
Max. Blade Size: 8-5/8″(220mm)
Main motor 4 HP 230 volts three phase
Depth of cut 2” max
Scoring unit with insert knives
Saw head rotates 90 degrees for rip or cross
cutting
Automatic shifting back grid
Two gauging bars with flip stop for midway
fenceBottom rollers with manual control for easy
movement of larger panels
Approx....