ID: 2310
Open
Listing ID: #2310 has been added to your wishlist.
PART: 2QM-R-RCGS-E - ROLLER COATER GLUE SPREADERS - 1, 2 SIDES - 24", 48", 63" WIDE
AMXmachine
Description
ROLLER COATER GLUE SPREADERS
PART: 2QM-R-.RCGS-1-24-1.75-E - GLUE SPREADER - 1 SIDE - 24” WIDE - 1.75” OPEN
PART: 2QM-R-RCGS-1-24-1.75-E - GLUE SPREADER - 2 SIDES - 24” WIDE - 1.75” OPEN
PART: 2QM-R-RCGS-1-48-1.75-E - GLUE SPREADER - 1 SIDE - 48” WIDE - 1.75” OPEN
PART: 2QM-R-RCGS-1-48-1.75-E - GLUE SPREADER - 2 SIDES - 48” WIDE - 1.75” OPEN
PART: 2QM-R-RCGS-1-63-1.75-E - GLUE SPREADER - 1 SIDE - 63” WIDE - 1.75” OPEN
PART: 2QM-R-RCGS-1-63-1.75-E - GLUE SPREADER - 2 SIDES - 63” WIDE - 1.75” OPEN
New with warranty
Photos & Features
Options:
Roll Guards (Hoods) for Operator Safety
Variable Speed Control (40-118 fpm)
6" Opening
Features:
• 1-sided Roller Coater (applies glue to 1 side [top side] of each panel) or 2- sided Roller Coater for 2-sided machine
• Working thickness: adjustable from 0 to 45mm (0 to 1.77"), adjustable via hand wheel
• Maximum material width: 630mm (24") or 1220mm (48”) wide or 1600mm (63”)
• Application rolls quantity: 1 or 2
• Application rolls material: SBR rubber, 60 durometer (Shore A)
• Application rolls diameter: 205mm (8") or 210mm (8.27”) for 48”, or 210mm (8.27”) for 63” wide
• Application rolls grooving: 20 grooves per inch
• Doctor rolls quantity: 1 or 2
• Doctor rolls material: Chrome-plated steel for 24” or NBR rubber, 98 durometer (Shore A) for 48” and 63” wide
• Doctor rolls diameter: 148mm (5.8") or 175mm (6.9”) for 48” and 63” wide
• Doctor rolls grooving: none (smooth rolls)
• Drive motor power: 1.5kw (2hp)
• Feed rate: fixed at 64fpm (optional: adjustable from 40 to 118 fpm)
• Includes emergency stop bars at front and back of machine
• Includes stainless steel waste glue drip pan
Note:
Electrical Requirements: 220v or 440v, 3-phase, 15 amps
The machine is designed to use water based PVA glue
For best glue for his application, your customer should consult his glue supplier (Franklin International, Wilsonart, etc.).
For countertops, we believe Wilsonart 3000 is quite popular
Payments & Returns
- Payment Methods
- Bank Wire Transfer
Post Message
Sign in to ask the seller a question.
AMXmachine
PART: 12532 - CROSS FEED SPLICER - KUPER
PART: 12532 - CROSS FEED SPLICER - KUPER
USED - VERY GOOD CONDITIONModel: ACR Superquick 3200Max. operating width in grain direction approx. 3200 mm Min. operating width in grain direction approx. 600 mm Width of the veneer strips across the grain from approx. 60 mm Veneer thickness approx. 0.3 – 2.5 mm Capacity up to 28 joints/min. Feed speed approx. 30 m/min.
Operating voltage 480 V, 3 Ph, 60 cycles
AMXmachine
PART: 2CA-RM30100AT-E - MULTI ROUND POLE – 1-1/8" x 4"
PART: 2CA-RM30100AT-E - MULTI ROUND POLE – 1-1/8" x 4"New with Warranty This RM30100AT is capable of producing multiple rods or two-sided moulding at high production rate.• It is built with top and bottom cutter spindle, typically for cutting wood board into round rods.• Suitable for cutting wood board into round rods. When cutters are replaced with planer cutter heads, this machine can perform double-sided planing or moulding.• It can use flat board without per-cutting.• Variable s...
AMXmachine
PART: AMX-10028 - DOBLE MITER SAW 45 DEGREE – 14” DIAMETER - PISTORIUS EMN-14
PART: AMX-10028 - DOBLE MITER SAW 45 DEGREE – 14” DIAMETER - PISTORIUS EMN-14
Used - Very good condition
2 Motors 2 HP,
208/230/460 Volts, 60 Hz, 3450 RPM
2 New On/Off
Switches with magnetic starters WEG
Saw harbor
5/8"
Dust exits 2 of
4" diameter, requres aprox. 850 CFM
Air use 72 CFM at
65 PSI based in 15 cycles/min
Table height
36-1/8" (917 mm)
Guide Left: 37” largo
Gude Right: 22”
largo
Pneumatic pedal
Each cut takes 4 to
6 seconds
Shippi...
AMXmachine
AFILADORA DE SIERRAS CIRCULARES
PARTE: 1HR-96687 - AFILADORA DE SIERRAS CIRCULARES - CHICAGO ELECTRICAFILA SIERRAS DIAMETRO 3-1/2" - 15-3/4"120V3800 RPMINCLUYE PIEDRA PARA AFILAR PUNTAS DE CARBURO DE TUGSTENO Y ACERO